Nothing Island Piece(Ferris wheel)——一个静谧的小公园 A quiet mini park

The English version is below

隆重介绍：Nothing Island 首个分体版本——Nothing Island Pieces

虽然外观接近 Nothing Island，但结构都是新的（如约1:14 减速齿轮组），而最重要的是，它实现了 100% 分件多色，总计 最多14色，单色打印机也可驾驭。

相比 Nothing Island，我重新设计了摩天轮舱位，主轮，传动轮，路灯，甚至为它加了个长椅

但分件多色的代价是，你需要 502 和一定的手工经验（哈哈）

由于是分体版，我就不写背景故事了，具体可以详见这里

五金清单：

1、创客新手套装（需要 030 电机*1，1:49.7 减速齿轮组*1，黄色橡皮筋*2，电池簧片*4，4*2 磁铁*10，连接线*2，BT3*8 螺丝若干）

2、3*30 直销轴*4 

另需要大量 502 胶水以粘连，内六角扳手拧螺丝

已知问题：传动噪音较大，摩天轮转动不平稳，后期会改进

对于所有传动结构，强烈建议上油/上蜡润滑，并打磨好所有毛刺，清除所有支撑，否则可能无法传动

虽然部件很精细，但已经试验过均可以在 0.4mm 喷嘴上打印且效果不错，个人觉得没有使用 0.2mm 喷嘴的必要，但组装要小心损坏零件。

虽然已经测试过，但由于不同打印机有不同公差，如果传动系统有问题或者拼装困难：

你看着办，能动，装上就行

推荐使用夜光耗材作为灯罩，木质耗材做长椅，如果没有也可以换成普通耗材配置中是我认为最佳的色彩方案，共 14 色，如果找不齐可以将相近颜色合并（其实连我耗材都找不齐哈哈）

提供详细 pdf 组装说明，无需担心组装困难问题

Grand Introduction: Nothing Island's First Modular Version — Nothing Island Pieces

Although it looks similar to Nothing Island, the structure is all new (such as the approximately 1:14 reduction gear set), and most importantly, it achieves 100% modular multi-color assembly, with up to 14 colors in total, which a single-color printer can also handle.

Compared to Nothing Island, I redesigned the Ferris wheel cabins, main wheel, drive wheel, lampposts, and even added a bench.

However, the price of modular multi-color assembly is that you need 502 glue and some hands-on experience (haha).

Since this is a modular version, I won’t write a background story.

For details, you can refer here.

Hardware List:

1. Maker Beginner Kit (requires 030 motor *1, 1:49.7 reduction gear set *1, yellow rubber bands *2, battery contacts *4, 4*2 magnets *10, connecting wires *2, BT3*8 screws, and some)

2. 3*30 direct-drive shafts *4Additionally, you'll need a large amount of 502 glue for bonding and an Allen wrench to tighten screws.

Known Issues: The drive is relatively noisy, and the Ferris wheel does not rotate smoothly — improvements will be made later.

For all drive mechanisms, it is strongly recommended to oil/wax and smooth out all burrs, and remove all supports, otherwise it may not rotate properly.Although the parts are very detailed, they have been tested successfully on a 0.4mm nozzle with good results.

Personally, I don't see the need to use a 0.2mm nozzle, but be careful during assembly to avoid damaging the parts.

Although tested, different 3D printers have different tolerances.

If the drive system has issues or assembly is difficult:Do as you see fit, as long as it works when assembled.

It is recommended to use glow-in-the-dark filament for lampshades and wood filament for the bench.

If unavailable, regular filament can be used. This is the color scheme I consider optimal, with 14 colors in total. If you cannot find all colors, similar colors can be merged (in fact, I can't even find all my filaments haha).

Detailed PDF assembly instructions are provided, so there is no need to worry about assembly difficulties.