Ice Blue Frost Skeleton Dragon Breath Lamp on Boot — Monitor Buddy

The moment your PC boots and the screen lights up, the Ice Blue Frost Skeleton Dragon's breath erupts in sync — raging fire bursts from its jaws and slams hard into the top of your monitor, the searing dragonflame streaming down the screen's edge! Every boot, you get that fantastical thrill of a dragon bearing down on your desk.

Sizes come in three tiers — 10 / 20 / 28cm. I'd start straight from 20 cm: a dual-colour print runs about 14 hours — it's the sweet spot between effect and print time, and that instant the dragonfire ignites on boot is the most worth it. Want maximum impact? Go straight for 28 cm — the extra time pays off the moment the flame comes alive. If you're really short on time, a 10 cm print works fine as a desk toy, though its flame can't take a light strip.

The lighting is simple: one 5V USB COB LED strip (1.5 mm, the thin-wire kind) is all it takes. Plug it into the USB port on the back of your monitor or straight into your PC, and it lights up with your machine the second it's plugged in. In China, search it on Pinduoduo, about ¥10. Overseas, search the same thing on Etsy、Amazon, Seeed Studio, or AliExpress. No LED strip on hand? Print it anyway — the light is what brings it to life, but you can always add it later.

Supports are already set up, so it's ready to print as-is. I've optimised them as much as I could; almost all contact surfaces are sloped angles, and both PLA and PETG release cleanly in my testing.

By default it mounts on the upper-right corner of your monitor. Want the upper-left instead? Just mirror the model — and remember to mirror the dragonflame too, or the parts won't line up.

I've put a lot of work into this one, so if you print it — I'd really love to see your make photo and a rating!!!!

————Monitor Wars Halloween Special Edition————

For Halloween, I'm releasing the special Halloween edition of Monitor Wars. This set includes four models depicting four scenes, Each scene can be printed and used individually. Turn the top of your monitor into a Halloween battlefield and make this Halloween unforgettable. Tap the title below to jump straight over.

Scene 1: The Ember Hell Flame Scale Dragon assaults the Pumpkin Castle, and the castle deploys its shield to fend off the dragon’s breath.

Scene 2: The shield shatters, and Pumpkin Castle is engulfed by dragonfire.

Scene 3: The Pumpkin Mage Apprentice struggles to hold his ground, pushing the dragon’s flame away from the castle.

Scene 4: The Grand Pumpkin Mage arrives and engages the dragon in an epic battle, with dragonfire and magic clashing violently in the air!

————Monitor Wars Standard Edition————

This is part of my Monitor Wars series. Print it on its own to play with, or pair it with other kits to make the monitor battlefield even richer. Print a set of the Lone Shield Warrior — a shield-bearer with a greatshield and a keen sword, standing alone in the dragon's breath, turning a lone dragon raid into the ultimate standoff between shield and flame. Or switch it up with the Ember Hell Flame Scale Dragon Breath Lamp — both dragons (the Ice Blue Frost Skeleton Dragon and the Ember Hell Flame Scale Dragon) share the same warrior kit and two different flame sets.

Tap the title below to jump straight over.

Shield Warrior vs Dragon Flame — Monitor Buddy

Ember Hell Flame Scale Dragon Breath Lamp on Boot — Monitor Buddy

Follow me if you want to catch new kits as they drop.

——Material Purchase Notes——

For the dragon flame filament, you can search 5V 1 .5 mm 360° COB USB LED strip from Etsy、Amazon etc. For a 20cm medium dragon, buy a 20cm strip; for a giant dragon, buy 26-30cm. Prices are similar, and you can trim any excess. For a 10cm mini version, the filament won't fit inside.

Etsy：5V 1 .5 mm 360° COB USB LED strip

Seeed：search for COB Strip 1.5mm

In china：pingduoduo

以下是中文简介

电脑开机、屏幕点亮的瞬间，冰蓝霜骸骨龙的龙息同步轰然迸发，汹涌烈焰自龙口喷涌而出，猛烈地撞击在你的显示器顶端，滚烫的龙焰顺着屏幕边缘流淌而下！每一次开机，都能感受巨龙来袭的奇幻氛围感。

尺寸分了 10 / 20 / 28cm 三档，建议直接从 20cm 起步——双色打印大约 16 小时，就能解锁开机龙焰同步点燃那一刻的惊艳。想要极致震撼直接就上28cm，多花的一点时间在龙焰燃起的瞬间会让你觉得都是值得的。

灯的设置很简单：一根 5V 1mm 360度 COB 灯带就够，插显示器背后的 USB 口、或者插主机上都行，插上就能和你的电脑一起亮。国内拼多多搜一下 10 块左右，海外的朋友在 Amazon、Seeed Studio 或 AliExpress 搜同样的关键词。手头没有灯带也照样能打——灯是让它活起来的那一笔，什么时候想加都行。

模型已经设置好支撑了，可直接一键打印。支撑已经尽可能优化过，绝大部分都是斜面，PLA 和 PETG 实测都能完整拆除。

安装默认是显示器右上角。要装左上角的话，把模型镜像一下即可——记得龙焰也要一并镜像，不然无法对位装配。

这是我非常用心做的模型，期待你的返图和评分！！！！

———— 系列联动 ————

本模型是我《显示器上的战争》系列作品，既可单独打印把玩，还可以搭配其他系列作品让显示器战场更有戏。去打一套《孤盾战士硬撼骸龙幽焰》——手持重盾和神剑的战士，孤身挡在龙息面前，把单纯的巨龙来袭，变成坚盾战士与龙焰的终极对峙。也欢迎换着玩《烬狱焚鳞魔龙息灯》，两条龙（冰蓝霜骸骨龙、烬狱焚鳞魔龙）都兼容同一个战士套件以及两套不同的龙焰。

关注我，新作第一时间能看到。